- Netcat For Windows Xp
- Netcat Windows Examples
- Windows Nc Command Search
- Windows Cmd Nc Command
- Netcat Commands Windows
- Windows Equivalent Of Nc
The command to have netcat listen on a specific port is “nc -l PORTNUMBER”. If you run this on a Windows 7 machine, you will get this dreaded message “local listen fuxored: INVAL”. The fix is to run it with a -L option. So the command would like this codenc -L -p 80/code The -L means “listen harder, re-listen on socket close”:). Nc -l host port – initiates a listener on the given port. Netcat Command Flags. Nc -4 – use IPv4 only. Nc -6 – use IPv6. Nc -u – use UDP instead of TCP. Nc -k -l – continue listening after disconnection. Nc -n – skip DNS lookups. Nc -v – provide verbose output. Netcat Relays on Windows. Nc host port relay.bat – open a. The subst command is a lot like the net use command in Windows except a local path is used instead of a shared network path. The subst command replaced the assign command beginning with MS-DOS 6.0. The subst command replaced the assign command beginning with MS-DOS 6.0. Former Windows Commander, a shareware 16 and 32 bit Explorer replacement for Windows, with enhanced search function, Built-in FTP client with FXP (server to server) and HTTP proxy support, and supports long filenames.
Netcat the Multi-purpose Networking Tool
May 02, 2020 Netcat Free Download for Windows 10/8/7 2020 – #1 Network Tool. Netcat is a utility used to write and read data across TCP and UDP network connections. You need to understand the capabilities of Netcat if you are responsible for network system or system security.
Linux netcat - nc command examples
netcat - nc - Utility
![Windows Nc Command Windows Nc Command](https://cdn.instructables.com/FF8/RB8Q/FF22CIDU/FF8RB8QFF22CIDU.LARGE.gif)
The netcat utility or nc is often referred to as the Swiss Army Knife for working with TCP/IP networks. This tool is very popular amongst System Administrators and Network Administrators because of its wide range of capabilities. The netcat utility is used for almost anything under the sun involving TCP, UDP, or UNIX-domain sockets. Netcat can open TCP connections, send UDP packets of data, listen on arbitrary TCP and UDP ports, carry out port scanning, transfer data from one server to another. In the following examples I will be using an Ubuntu 14.04 LTS system and a CentOS 6.5 system.
Installing netcat on Ubuntu
If you need to install netcat, you can use the following commands:
Note: In Ubuntu 14.04 LTS netcat came pre installed. (No need to install)
Installing netcat on RHEL - CentOS
To install netcat on a RHEL/CentOS system (64bit), simply issue the following command: yum install nc.x86_64
Examples of netcat networking utility
In the following examples we will take a quick look at some of the popular uses of netcat.
Checking for an Open Port
Netcat For Windows Xp
In this example we will use netcat to interrogate a port to see if it is open. We will use the netcat command in conjunction with the '-v' and '-n' flags. The '-v' flag specifies that we would like verbose output (more detailed). The '-n' option specifies that we do not wish to use DNS or service lookups on any addresses, hostnames or ports.
Example Command: nc -vn 192.168.0.17 22
In the above example we have specified the IP address of a RHEL (Red Hat Enterprise Linux 6.3) server followed by the port we wish to interrogate. In this example we are looking at port 22 (normally used for ssh).
Example Command: nc -vn 192.168.0.17 22
In the above example we have specified the IP address of a RHEL (Red Hat Enterprise Linux 6.3) server followed by the port we wish to interrogate. In this example we are looking at port 22 (normally used for ssh).
As we can see from the output port 22 is open for connections. If we now check for a port which is closed, you will see the difference in the output from the command:
Netcat Windows Examples
netcat as a Port Scanner
Another popular use of the netcat command is to use it as a port scanner. In this example we will be using the flags '-w' and '-z' in addition to the '-v' and '-n' flags. The '-w' flag is used to specify a timeout limit. By default, netcat will listen forever, however, in this example we are going to use a more realistic value of '1' second. The '-z' flag specifies that netcat should merely scan for listening daemons without sending any data. We will also specify a range of ports to check. In this example we are only going to check ports 1 through to 30.
Example Command: nc -vnz -w 1 192.168.0.17 1-30
Example Command: nc -vnz -w 1 192.168.0.17 1-30
We can clearly see from the above output that a connection to port 22 has succeeded.
You can also specify more than one port to scan.
Example Command: nc -vnz -w 1 192.168.0.17 20 21 22 23 24 25
In the above example, we are going to scan ports '20, 21, 22, 23, 24 and 25'.
You can also specify more than one port to scan.
Example Command: nc -vnz -w 1 192.168.0.17 20 21 22 23 24 25
In the above example, we are going to scan ports '20, 21, 22, 23, 24 and 25'.
Port Scanning UDP ports
In this example we are going to specify 'UDP' ports to be scanned. To specify UDP we will use the '-u' flag. In the example below we are going to scan ports '60 through to 80'.
Example Command:nc -vnzu -w 1 192.168.0.17 60-80
Example Command:nc -vnzu -w 1 192.168.0.17 60-80
Having a Chat with Netcat
In this example we will use an Ubuntu 14.04 LTS terminal and connect this to a remote terminal on a CentOS 6.5 Server.
On the Ubuntu system, we need to identify the IP address. This can be done by issuing the command ip a s
On the Ubuntu system, we need to identify the IP address. This can be done by issuing the command ip a s
From the above we can see that the IP address in use on interface 'eth0' is 192.168.0.11
This IP address is only needed by the CentOS server. Now, on the Ubuntu system we issue the following command:
nc -lp 2468Here we are instructing netcat to listen on port 2468.
This IP address is only needed by the CentOS server. Now, on the Ubuntu system we issue the following command:
nc -lp 2468Here we are instructing netcat to listen on port 2468.
Now on the remote CentOS server we issue the following command:
nc 192.168.0.11 2468
nc 192.168.0.11 2468
Windows Nc Command Search
Windows Cmd Nc Command
Here we are telling our CentOS server to make a connection to our Ubuntu system on port 2468.
Now any text typed on one terminal will now appear on the other terminal screen. (Warning, this is not a secure way to chat!)
Ubuntu System
Now any text typed on one terminal will now appear on the other terminal screen. (Warning, this is not a secure way to chat!)
Ubuntu System
Output received on CentOS system
For more information regarding netcat/nc command
As always a vast amount of information can be looked at via the man pages. To view more information regarding netcat, issue the command man nc